Version: 2022.1
LanguageEnglish
  • C#

Rigidbody.AddForce

Suggest a change

Success!

Thank you for helping us improve the quality of Unity Documentation. Although we cannot accept all submissions, we do read each suggested change from our users and will make updates where applicable.

Close

Submission failed

For some reason your suggested change could not be submitted. Please <a>try again</a> in a few minutes. And thank you for taking the time to help us improve the quality of Unity Documentation.

Close

Cancel

Switch to Manual

Declaration

public void AddForce(Vector3 force, ForceMode mode = ForceMode.Force);

Parameters

force Force vector in world coordinates.
mode Type of force to apply.

Description

Adds a force to the Rigidbody.

Force is applied continuously along the direction of the force vector. Specifying the ForceMode mode allows the type of force to be changed to an Acceleration, Impulse or Velocity Change.

The effects of the forces applied with this function are accumulated at the time of the call. The physics system applies the effects during the next simulation run (either after FixedUpdate, or when the script explicitly calls the Physics.Simulate method). Because this function has different modes, the physics system only accumulates the resulting velocity change, not the passed force values. Assuming deltaTime (DT) is equal to the simulation step length (Time.fixedDeltaTime), and mass is equal to the mass of the Rigidbody the force is being applied to, here is how the velocity change is calculated for all the modes:

  • ForceMode.Force: Interprets the input as force (measured in Newtons), and changes the velocity by the value of force * DT / mass. The effect depends on the simulation step length and the mass of the body.
  • ForceMode.Acceleration: Interprets the parameter as acceleration (measured in meters per second squared), and changes the velocity by the value of force * DT. The effect depends on the simulation step length but doesn't depend on the mass of the body.
  • ForceMode.Impulse: Interprets the parameter as an impulse (measured in Newtons per second), and changes the velocity by the value of force / mass. The effect depends on the mass of the body but doesn't depend on the simulation step length.
  • ForceMode.VelocityChange: Interprets the parameter as a direct velocity change (measured in meters per second), and changes the velocity by the value of force. The effect doesn't depend on the mass of the body or the simulation step length.

Force can only be applied to an active Rigidbody. If a GameObject is inactive, AddForce has no effect. Also, the Rigidbody cannot be kinematic.

By default the Rigidbody's state is set to awake once a force is applied, unless the force is Vector3.zero.

See Also: AddForceAtPosition, AddRelativeForce, AddTorque.

This example applies a forward force to the GameObject's Rigidbody.

using UnityEngine;

public class Example : MonoBehaviour { Rigidbody m_Rigidbody; public float m_Thrust = 20f;

void Start() { //Fetch the Rigidbody from the GameObject with this script attached m_Rigidbody = GetComponent<Rigidbody>(); }

void FixedUpdate() { if (Input.GetButton("Jump")) { //Apply a force to this Rigidbody in direction of this GameObjects up axis m_Rigidbody.AddForce(transform.up * m_Thrust); } } }

Declaration

public void AddForce(float x, float y, float z, ForceMode mode = ForceMode.Force);

Parameters

x Size of force along the world x-axis.
y Size of force along the world y-axis.
z Size of force along the world z-axis.
mode Type of force to apply.

Description

Adds a force to the Rigidbody.

This example applies an Impulse force along the Z axis to the GameObject's Rigidbody.

using UnityEngine;

public class Example : MonoBehaviour { public float thrust = 1.0f; public Rigidbody rb;

void Start() { rb = GetComponent<Rigidbody>(); rb.AddForce(0, 0, thrust, ForceMode.Impulse); } }
Copyright © 2023 Unity Technologies
优美缔软件(上海)有限公司 版权所有
"Unity"、Unity 徽标及其他 Unity 商标是 Unity Technologies 或其附属机构在美国及其他地区的商标或注册商标。其他名称或品牌是其各自所有者的商标。
公安部备案号:
31010902002961